07
Note: Because network cable is made of pair cores, if there is open circuit,
it will show faults in pairs, just as above "4" &" 5". it means either "4" pin
or "5" pin exsits an open circuit, or both "4" and "5" exsit an open circuit.
Test result 5: In case of open circuit existing at the near end of
the cable , the following interface
is shown:
when testing only with main tester
In the figure, “X” shown in “3” and “6” pin position in “M” line, indicates there is
open circuit in “3” and “6” pin of the near pin.
Test result 6: In case of open circuit existing at the middle part
of the cable , the following interface
is shown:
when testing only with main tester
In the figure, “X” shown in “3” pin position in “M” and “S” line, indicates there is
open circuit in “3” pin of the middle part of the cable. Perform"PAIR&LENGTH"
to locate the exact fault point. Refer to the related chapter below.
1 2 X 4 5 X 7 8
M:
S:
1 2 3 4 5 6 7 8
Wi r e Ma p : Loc al
Test result 7: In case of open circuit existing in the cable when
testing with main tester and remote unit together, the following
interface is shown:
1 2 3 X X 6 7 8
M:
S:
1 2 3 X X 6 7 8
Wi r e Ma p : Loc al
In the figure, “X” shown in “4” & “5” pin in “M” & “R” line, It has two possible results.
Both “4” and “5” pin are open curcuited. Or , either “4” or “5” pin is open.
Note: When checking wiremap with main tester and remote unit together,
the cable is tested in pair. Thus, if there is one pin is open , it will show in pair
as above.
To test which pin is open, users can check wiremap only with main tester like
Example 4,Example 5 and Example 6 do.
1 2 X 4 5 6 7 8
M:
S:
1 2 X 4 5 6 7 8
Wi r e Ma p : Loc al
08
Test result 9: 6-core telephone cable line sequence test
At this time, press any key to return to the main menu, and then press
“ENTER” key for re-test.
Test result 10: BNC coaxial cable line sequence test
efore checking wiremap of telephone cable, users need to choose "TEL(6)"
in . and then return to main menu to check its wiremap. If the
testing cable is in good connection, it will displays as follows:
"Type"
Before checking wiremap of BNC cable, users need to choose "BNC(2)"
in . and then return to main menu to check its wiremap. If the
testing cable is in good connection, it will displays as follows:
"Type"
1 2 3 4 5 6
M:
R:
Wire Map: Remote
1 2
M:
R:
1 2
Wire Map: Remote
At this time, press any key to return to the main menu, and then press
“ENTER” key for re-test.
Test result8: USB cable line sequence test
Before checking wiremap of USB cable, users need to choose "USB(4)"
in "Type" . and then return to main menu to check its wiremap. If the
testing cable is in good connection, The following interface will be shown:
At this time, press any key to return to the main menu, and then press“ENTER”
key for re-test.
1 2 3 4
M:
R:
1 2 3 4
Wire Map: Remote
1 2 3 4 5 6
Your excellent helper in cable test!
Your excellent helper in cable test!
(12 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals